V-Twin Manufacturing

Twin Cam chain shoe tool is used to remove and replace the spring loaded cam chain tensioners. Saves hours of the mechanics time! *NOTE: Must order chain tensioners and related components as required. 1999-2006 FL 2000-2006 FLST 2000-2006 FXST 1999-2005 FXD

0-Front

Chrome end caps for straight pipes with a outer diameter of 2-1/4

Black fishtail muffler set without baffles features a 3" body outer diameter and is for M8 models. Sold in a quantity of 2.
**CAUTION: These exhaust products are not legal for sale or use in California on pollution-controlled vehicles. These products are intended for non-highway only.

2017-UP FLT

Length 34-1/2"

Polished oil collector is designed to collect the oil mist from the breather hose which eliminates engine oil from collecting in air cleaner. On top is a high flow air filter that acts as a baffle allowing the oil and air to separate more efficiently and can easily be cleaned. On the bottom is a drain plug to allow drainage on a regular basis. A 90° barbed fitting fits breather hoses perfectly and includes chrome mounting billet clamp. *NOTE: Order strp steel clamp if prefered ehich can then be cut to length. *NOTE: So the clamp does not slip when you tighten the fittings it's s
40-0569" Liquid filled 60lb oil pressure gauge features a silver face stainless steel case chrome rim and weather resistant sealed lens. This liquid filled face eliminates needle bounce giving a constant reading. Gauge has a 1/8 National Pipe Thread male rear fitting. Custom application

Saddlebag latch rivet tool gives secure fastening of rivets while providing a clean factory look. Use to crimp saddlebag latch and hinge rivets. 0-All Models

Chrome 4-1/2" bullet style trim set is held in place by existing bulb and rim.

Chrome 2 into 1 exhaust lake style header pipes are designed to look like the hot rod side exhausts with 12mm oxygen sensor bungs. Includes heatshield and hardware. The turn out end is 3 in diameter. Fits with controls only. Header pipes are 1-3/4 with 16 gauge steel construction. Accepts 12mm oxygen sensor units bungs may be plugged for earlier applications. Will also work on many Rigid Chopper and Bobber models with left side drive.

**NOTE: These pipes will not work with floorboards. Collector is not baffled. 

2012-2017 FXST 
2012-2017 FXDWG

Male end mount railroad footpeg set.
Overall length of footpeg set is 5.9" and end to end without mount is 4.02".

Universal 18" chrome heat shield for use on 2" exhaust pipes. Includes clamps for installation. Custom for 2" pipes"

Ironhead LAF style header set features a chrome finish. *NOTE: Pipes attach to each other at the end. Additional mount bracket may be fabricated to mount set to frame. 1957-1985 XL

Indian Scout short type drag pipe set features a black finish with straight pipes with white exhaust wrap. Pipe set is finished in heat proof black.

*NOTE: Pipes are equipped with O2 sensor ports.
*NOTE: Pipe set can be baffled with insert, available separately.
**NOTE: UPS may consider this part as packaged "oversize" for shipment, as compared to the actual weight, which will result in higher shipping costs.

2015-UP Scout

Black 1-1/4 handlebar is knurled and drilled for internal wiring. *Note: UPS may consider this part as packaged oversize for shipment as compared to the actual weight which will result in higher shipping costs. 1974-1981 FL 1974-1981 FX 1974-1981 XL

Final drive steel 27 tooth front pulley. *NOTE: Must order nut and lock kit separately. 1991-2003 XL 883, 883C, 883 HUG, 883R

Sifton wrist pin bushing reamer tool is easy to use with their design lead in taper at the start of each ream. Order rod clamping tool separately. This tool is used to secure the rod while performing the reaming operation. The front of the taper is .767 body for actual reamed hole is .792 . 1936-1952 EL 1941-1984 FL 1985-1999 FL 1937-1952 WL 1937-1973 G 1937-1948 U

Replica rear fender uses a specific tail lamp and includes indent for the turn signal bar.
Outside width of fender is 7-1/4". Inside width measures 7". We suggest pre fitting the fender prior to painting.
OEM: 59144-06

T

Strutless rear fender is 2mm thick and has a width of 12.75" and constructed of steel. Fender will cover 280-300 series tire.
Let V-TWIN help you with that wide tire conversion. These strutless rear fenders will fit over the new tire and attach to the stock width frame. Fender will bolt to frames 11" wide where strut mounts. The width of the inside of the fender where it ataches to the frame measures 12-1/4". The stock strut supports must be removed from the frame. We suggest pre fitting the fender prior to painting. Position cut drill mount holes as required.

Strut Outer Width: 13-3/4"